SPECIFICATIONS FOR DECK CONSTRUCTION
WHY USE ECO BAMBOO AFRICA COMPOSITE DECKING?
- BAMBOO COMPOSITE DECKING is comprised of 70% Bamboo fiber, 20% Recycled HDPE and 10% additives (dyes and resin)
- This product is ideal for the vast diversity of the African climate with low maintenance, which makes it ideal for holiday homes and high traffic areas. Requires
- NO yearly refinishing like its wooden counterpart – Hardwood Decks
- Insect and water resistant
- Slip and splinter proof
- ECO BAMBOO AFRICAS COMPOSITE DECKING is available in; 5.8m x 150mm x 23mm and 4m x 150mm x 23m each plank weighing approx. 18kgs
- Joist spacing of no more than 350mm OC (on centre) is specified for ECO BAMBOO AFRICA COMPOSITE DECKING.
- Although the initial cost of the COMPOSITE DECKING is similar to that of Hardwood decking, the longevity of this material and the fact that it has no maintenance, offsets the initial cost within the first 3 to 5 years.
- ECO BAMBOO AFRICA COMPOSITE DECKING is issued with a 10 year warranty.
Smooth vs Reeded Composite Decking
- 150mm x 23mm ECO BAMBOO AFRICA COMPOSITE DECKING is attached to joists using a stainless steel clip system that fit into the side slots of the planks.
- These are fastened with 75mm stainless steel screws (Clips and screws included)
- NO NAILS OR SCREWS ARE TO BE USED THROUGH THE PLANKS, as this could lead to splitting of the BAMBOO COMPOSITE DECKING planks.
- If deck boards are not of sufficient length to cover the entire span of the deck, joints must be staggered to ensure greater strength and all joints must butt on a joist.
- BAMBOO COMPOSITE DECKING is automatically spaced by the Clip system at 5mm apart to facilitate ease of cleaning and allows for natural expansion and contraction. As BAMBOO COMPOSITE DECKING already comes with its final brushed finish, markings that do occur during installation can be treated with a wire brush.
- Like a wood composite decking, ECO BAMBOO COMPOSITE DECKING also expands, although this is less than with polypropylene or polyethylene based decking products.
- The expansion occurs due to 2 reasons. It is important to understand these reasons, as it directly influences the correct installation of the decking and providing adequate expansion joints.
During the manufacturing process, all moisture is removed from the wood content of the BAMBOO composite decking. After installation, the product will re-absorb some moisture up to about 6%. The locality of the deck i.e. coastal, Highveld or next to a swimming pool, will determine the level of re-absorption. This moisture re-absorption leads to a once-off one-directional expansion of the decking (length wise).
- The second form of expansion occurs due to fluctuations in day- and night temperature. During the heat of the day, the planks will expand and during cooling off at night, the planks will contract. This is therefore a recurring bi-directional expansion
- During installation, expansion gaps should be left to allow for both types of expansion. This might lead to fairly large expansion gaps to be left initially, which will close somewhat during moisture uptake. It is important to explain to clients that these gaps will close as the expansion takes place over a period of a month or two.
- The guideline for expansion gaps are as follows. Please note that this is only a guideline and that the specific locality of the deck should be taken into account:
- Decking Corners – when BAMBOO COMPOSITE DECKING corners are used to finish off the end of a deck, it is important to fix the corner to the ends of the decking planks and NOT the sub-structure, to allow the corner to move with the planks during expansion.
- Cladding – when using BAMBOO COMPOSITE DECKING to clad the sides of a deck, it is better to use the planks in a vertical configuration than in horizontal lengths.
Substructure which CANNOT be treated after assembly and should be treated with at least two coats of Carbolinium. One prior to assembly and one post assembly.
Creosote can also be used for treatment, but in warmer climates creosote tends to sweat and drip causing damage to anything under the substructure.
BAMBOO COMPOSITE DECKING are UV stabilised for a period of 10 - 15 years.
Actual UV stability may vary due to specific sun exposure. Once deemed necessary the Composite decking can be treated with teak oil or similar products to bring back the original darker colour.
NB: Varnish or other film forming treatments should NEVER be used on decks as these treatments fail due to the fact that they cannot withstand the moisture / heat / UV cycles that decks are exposed to.
All fasteners, screws, nails or other metal used with the clip system should be stainless steel.
PLEASE NOTE: IMPROPER INSTALLATION WILL VOID THE WARRANTY ON THE DECKING!
GENERAL GOOD DECKING INSTALLATION AND DESIGN PRACTICE
- On span of 2.5 metre or less, girders must be at least 50 x 228 mm;
- On span of2.5 metre to 3.5 metre, girders must be at least 76 x 228 mm;
- If deck size is more than 3.5 metre two or three spans as mentioned in 1 and 2 above must be used.
Girders must be securely attached to reinforced concrete pillars or creosote/CCA (Copper Chromate Arsenate) treated poles of minimum diameter of 150 mm, set in a concrete base.
Where girders are parallel to and attached directly to walls, 8mm Rawl bolts spaced at no more than 600mm should be used for 2,5 metre span and 10mm Rawl bolts spaced at no more than 600mm should be used for span greater than 2.5 metre.
Where girders are attached to walls at an angle, Galvanized/Stainless Steel girder hangers must be used. Girder hangers must be attached to the wall with at least two (2) 10mm Rawl bolts and girder must be attached to hanger with at least one 8mm bolt or coach screw.
Note: Standard galvanised girder/joist hangers manufactured of 1.5mm sheet metal are not recommended. Girder/joist hangers should be manufactured of 50x50x5mm angle iron and be hot dipped galvanised. H stainless steel is used for the manufacture of girder/joist hangers, thinner material can be used.
- On 2.5 metre span, or less, joists must be at least 50 x 152 mm;
- On span of 2.5 to 3.5 metre, joists must be at least 50 x 228 mm.
Depenant on the location of the deck (private or public), joists must be spaced at intervals of between 300 OC (on centre) Joists must be attached to Girders with Galvanized/Stainless Steel joist hangers (See above note on girder/joist hangers) with 10 x 75mm coach screws or notched for and attached with a 50 x 76 mm ledger strip. Rim joists, that is joists on the outer edge of a deck, where joist hangers cannot be used, can be attached to girders with two (2) 10 x 125mm or 13 x 150mm Coach screws, dependant on the thickness of the girder.
1. As in the case of a house, the substructure of a deck is the foundation of the deck. Inferior materials and/or specifications should therefore never be used for the construction of the substructure, as the strength of the deck relies entirely on the strength of the substructure.
2. For safety purposes decks should be designed for a carrying capacity of 250 kilograms per square metre (50 pound per square foot). Of this one fifth, or 50kg is dead weight, i.e. the weight of materials, and four fifths, or 200kg is live weight, that is the weight of furniture, people etc.
The design and positioning of stairs are critical for safety and comfort of use. According to regulations stairs should be designed within the following parameters:
Step elevation from the top of one step (raisers) to the top of the next should be between 160 and 180mm;
Step tread width should be between 250 and 300mm with a maximum step overhang of 10mm with the next step; and staircase incline should never exceed 38 degrees.
Needless to say that stairs should be very sturdy and tread boards (raisers) should be very strong.
The above are the minimum specifications for normal usage decks. Each deck is, however, individually designed for the purpose for which it will be utilised. If, for example, the owner intends to install a Jacuzzi on the deck, a much stronger substructure will be required. The same will be applicable if the deck will be used as a public amenity where no, or little control can be exercised on the number of persons on the deck at any one time. All possible factors should be taken into consideration with the design and construction of any deck.
Where public liability exists:
- Girders should always be 76 x 225mm and span of 3 metres should never be exceeded;
- Joists should always be 50 x 228mm and span of 3 metres should never be exceeded; and
- Joist spacing should always be on a factor of 10, therefore 250mm.
Some of the Decking Colors Available
A now completed project just outside Paarl in the Boland. You can already see how bamboo composite decking transforms and creates spaces that are incomparable in style, quality, and design. An architects dream and a timeless piece that lasts a lifetime.
We've already highlighted the many advantages of our composite decking over other plastic decking but below we wish to show you some of the stunning installations done by our installation agent, Bamboo Warehouse, in South Africa. Our durable and low-maintenance decking boards come in a variety of colors and its ease of installation makes almost any deck design idea possible.
Composite Decking Installation
Our decking boards can transform any area into a stunning living space as shown by the transformation of this area below, creating an elegant and professional entertainment space.
Bamboo Paneling Installation
The versatility of Bamboo is shown below for use as wall paneling, creating a stunning effect as well as hiding unsightly cabling and plugs.
Bamboo Stairway and Railing Installation
In this installation we see the transformative effect of Bamboo used in the stairway as well as in the railing.
Contact us today to enquire about our competitive decking prices as well all our other bamboo products. Eco Bamboo Africa: the leading distributor of bamboo products to the Namibia, Botswana, Zambia, Kenya and the rest of the African continent.
Below are a few examples of how composite decking can transform your home, increase its value and add a feeling of spaciousness to any area. It's tranformed the space into an inviting destination for taking in the stunning view. Click here to contact us today to find out more about composite decking or to request a quote. Installation done by our South African associates and installation agent Bamboo Warehouse.
Near-zero maintenance: Our composite decking is designed to resist weathering, warping and insects which means you won’t need to replace rotting or damaged boards as with wooden planks. You don’t need to paint, seal or stain it which means no yearly maintenance costs.
Safety: Composite Decking is slip-resistant and splinter-free making your home, lodge or hotel safer for children or guests.
Durability: The African continent is known for its varied and extreme climate. From thunderstorms and hail to the blistering heat, our decking can stand up to the harshest elements. With composite decking there is minimal fading and it is UV Stabilized, which helps to protect it against the African Sun.
Colors: Composite decking comes in a wide range of colors to match and complement your home or lodge.
Eco-friendly: It is made up of 60% bamboo and 40% recycled plastic, which makes it not only green but also extremely tough, stable and durable. This makes it a favorite among environmentally minded people.
Defect Free: Use the entire product with less waste at the end, bringing down the cost of the project.
Long Term Cost Savings: Wood decking may be less expensive in the beginning but won’t save you money in the long term. With Composite decking there is no on-going maintenance as with wood, such as cleaning and sealing every few years.
Less Nails and Screws: Your deck will have a visually pleasing smooth surface and no rusty nails or screws!